Beruflich Dokumente
Kultur Dokumente
INSPECTION REPORT
Kunde
Customer
Taiho, Japan fasor 7 Ujhartyan, Hungary
Zweck
Item
Calibration and maintenance
Modell
Model
Surfcom contourrecord 1600 D
Hersteller
Manufacturer
Accretech Tokio Seimitsu
S/N
Serial N°
KA8207HR
Die in diesem Prüfbericht enthaltenen Messergebnisse wurden, auf der Grundlage der in diesem Bericht erwähnten Prüfvorschriften, erzielt
und die Angaben der verwendeten Messnormale garantieren die Rückführbarkeit zu nationalen bzw, internationalen Standards,
Des Weiteren wurden Angaben zu den Prüfzertifikaten dieser Normale und zur Gültigkeit gemacht, Die erzielten Messergebnisse beziehen
sich nur auf diese Normale, den Ort der Messung und die vorhanden Umgebungsverhältnisse zum Zeitpunkt der Messung,
The measurement results reported in this Report were obtained following the measuring procedures (methods) given in the following page,
where the reference standards or instruments are indicated which guarantee the traceability chain to national and/or international standards,
and the related calibration certificates in the course of validity are indicated as well, They relate to the measured item only and they are valid
for the time, the place and conditions of measurements, unless otherwise specified,
Dieses Prüfprotokoll darf nur vollständig vervielfältigt und weitergegeben werden , Seite
This certificate shall not be published or reproduced other than in full, Page 1/3
Die Überprüfung erfolgte nach Anweisung DT16800-M001-E2, erstellt durch ACCRETECH Tokio Seimitsu,
Das Messgerät wurde von Accretech beim Auftraggeber überprüft, Die Überprüfung umfasste die zum Nachweis der geforderten
Qualitätsmerkmale und Messgenauigkeit notwendigen Prüfungen und Messungen, die in den beiliegenden Protokollen
dokumentiert sind, Die Überprüfung erfolgte nach Herstellerspezifikation und liegt innerhalb der vorgeschriebenen Toleranzen,
The verification, object of the present Measuring Report has been performed following the suitable procedure in the document
DT16800-M001-E2, compiled by ACCRETECH Tokyo Seimitsu,
The present Measuring Report concerns the verification of the performances of the measuring system as indicated tin the first
page of this document, The test has the purpose to verify that the errors of indication obtained on the measuring system are
within the tolerances specified by the manufacturer and suitable with the values MPE (Maximum Permissible Error), For the
verification of the measuring instrument, some masters are used for the control of roundness, flatness, straightness and
parallelism,
Entsprechend
According to JIS B7451/1997 (ISO 3274/1997)
Dieses Prüfprotokoll darf nur vollständig vervielfältigt und weitergegeben werden , Seite 2/3
This certificate shall not be published or reproduced other than in full, Page
• Vibrations Test
Masterball
2.5mm
Radius 6,34979mm 6,3501mm 0,31µm Roundness +/- 5µm OK
Roundness 1,63µm 0,05µm 1,58µm Radius 5µm
10mm
Radius 6,35048mm 6,3501mm 0,38um Roundness +/- 5µm OK
Roundness 1,63µm 0,05µm 1,58µm Radius 5µm
25mm
Radius 6,35054mm 6,3501mm 0,44um Roundness +/- 5µm OK
Roundness 1,74µm 0,05µm 1,69um Radius 5µm
Die Ergebnisse wurden ebenfalls auf dem Systemcomputer, unter C:/Data/Service Accretech/20180115
The results are saved also on the system PC under C:/Data/Service Accretech/20180115
T= 22,5° C
Dieses Prüfprotokoll darf nur vollständig vervielfältigt und weitergegeben werden , Seite 3/3
This certificate shall not be published or reproduced other than in full, Page
Symbol Actual
Line (Line) [Line_1]
Straightness 0.00090 mm
Name of item Content
Symbol Actual
Line (Line) [Line_1]
Straightness 0.00074 mm
Name of item Content
Symbol Actual
Line (Line) [Line_1]
Straightness 0.00095 mm
Name of item Content
Symbol Actual
Circle (Circle) [Circle_1]
Radius 6.34979 mm
Roundness 0.00163 mm
Name of item Content
Symbol Actual
Circle (Circle) [Circle_1]
Radius 6.35048 mm
Roundness 0.00163 mm
Name of item Content
Symbol Actual
Circle (Circle) [Circle_1]
Radius 6.35054 mm
Roundness 0.00174 mm
Jan Calibration
2019 Certificate